← Home / Circuits / Figure 01

LM386.

A real, low-voltage audio-amplifier circuit—documented against Texas Instruments SNAS545D. The external diagram follows the manufacturer's bass-boost application and adds clearly identified supply filtering. The internal view is a functional topology map; the exact transistor schematic is linked from TI.

9 V DCsingle supply
8 Ωspeaker load
≈700 mWLM386N-3, typical at 10% THD
01 / EXTERNAL APPLICATION

Wiring schematic.

Source circuit: TI datasheet Figure 9-9 (bass boost). The 10 µF capacitor on bypass pin 7 and the 100 nF + 100 µF supply capacitors are the extra local decoupling shown here. The 9 V source and 8 Ω load are within the documented application range.

Complete labeled LM386 bass boost circuit showing the 9V supply, decoupling capacitors, ten-kilohm volume potentiometer, pins one through eight, bypass and feedback networks, output Zobel RC, coupling capacitor polarity, and eight-ohm speaker
Illustrated external wiring / TI-derived engineering drawing / click for unlimited SVG zoom.
Not a 5 W amplifier. TI lists the LM386N-3 at a typical 700 mW with 9 V supply and an 8 Ω load at 10% total harmonic distortion. A speaker rated 5 W is compatible as a load when its impedance is 8 Ω, but the amplifier does not deliver 5 W.
02 / INTERNAL TOPOLOGY

Inside the LM386.

Documented groups include the 50 kΩ input bias paths, the 15 kΩ bias chain, 150 Ω and 1.35 kΩ gain-setting resistors, bipolar transistor input and driver stages, output bias diodes, and class-AB output stage. The map explains their roles; it is not a replacement for TI's complete transistor-level schematic on page 1.

Internal topology map with input transistor pair, resistor gain and bias circuitry, driver and class AB output stages, and actual resistor values from the manufacturer
Functional illustration derived from manufacturer documentation; internal transistor connections are not intended as a build netlist.
03 / GAIN CONTROL • OPTIONAL REFERENCE

Change the gain, not the wattage.

Gain depends on the external connection between pins 1 and 8. These three alternatives are grounded in TI sections 9.2.1–9.2.3. They are separate circuit configurations, not parts to add simultaneously to the 9 V bass-boost drawing above.

Three alternative LM386 gain connections: pins 1 and 8 open for gain 20; 1.2 kiloohm resistor plus 10 microfarad capacitor in series for gain about 50; 10 microfarad capacitor alone for gain 200. Positive capacitor terminal faces pin 1.
Alternative networks across pins 1 and 8. Manufacturer-based configurations, not a drop-in modification of the featured bass-boost circuit.
Keep the current FIG. 01 unchanged if building it. The bass-boost configuration has pin 8 open and a separate RC feedback path from pin 1 to pin 5. Adding a gain capacitor changes compensation and requires reviewing TI's resistor limits, input bypassing and stability guidance. Higher voltage gain does not imply greater output power.
04 / BILL OF MATERIALS

Components and connections.

The values listed below match the displayed external schematic. Use a suitably rated regulated 9 V DC supply; the grounding symbols indicate one common return.

RefValue / partConnection / function
U1LM386N-3 or compatible 9 V LM386 variantPin 6 to +9 V; pins 2, 4 to GND; pin 8 open.
RV110 kΩ potentiometerAudio input to high terminal; low to GND; wiper to pin 3 (+IN).
C1250 µF electrolytic, ≥16 VSeries output coupling: positive terminal toward pin 5, negative toward 8 Ω speaker.
C2 + R150 nF capacitor + 10 Ω resistorSeries Zobel network: output pin 5 to ground. Neither part is directly across the speaker.
C3 + R233 nF capacitor + 10 kΩ resistorSeries bass-feedback RC from pin 1 to pin 5, before C1. Pin 8 remains open.
C510 µF electrolytic, ≥16 VBypass from pin 7 (+) to ground (−); noise reduction.
C6100 nF ceramic, ≥16 VLocal +9 V to GND bypass at pin 6; engineering addition.
C7100 µF electrolytic, ≥16 VAdditional +9 V to GND bulk decoupling; positive to +9 V.
LS18 Ω speaker, 1 W or higher ratingAfter the output capacitor to ground. A 5 W-rated speaker is also suitable.
Polarity & assembly: Keep the supply decoupling close to U1. Observe capacitor polarities and confirm ground continuity before powering. If the audio source carries DC offset, add suitable input AC coupling. Power off before changing wiring. Crossed conductors without junction dots are independent.
05 / SOURCE AND LIMITS

Datasheet references.

Texas Instruments, LM386 Low Voltage Audio Power Amplifier, SNAS545D (2023). See page 1 for the real internal transistor schematic, page 5 for measured output-power ratings, page 10 for gain and bass-feedback theory, pages 12–13 for gain alternatives, page 15 for Figure 9-9, and page 17 for supply-decoupling guidance.

The SVG is an original re-drawing of the external application connectivity with documented additions. It has been reviewed for component/pin consistency but not physically built, simulated, or tested. Do not treat the internal topology illustration as an electrical wiring schematic.